Date: Mon, 8 May 89 11:42:21 PDT

From: (Fred Lloyd)

To: MBRAMWEL
Subject: TM-721A UHF Extend Mod







Modifying the Kenwood TM-721A for Extended UHF Coverage



Well I finally uncovered the specifics of the mod which will extend the

UHF coverage of the TM-721A.  This mod changes the UHF receive from

it's factory setting of 438 - 449.995 mhz to approximately 420-460

MHZ.  There are some peculiarities surrounding this mod so I'll

describe them first.



First of all, this mod will allow the UHF digital display to traverse

from 400.000 to 499.995.  The radio will not, however, tune this entire

range due to a combination of a limited synthesizer lock range and the

input RF amplifier bandwidth.  The apparent useful tuning range is

about 420-460, with sensitivity dropping off sharply at either end.

Naturally, the best performance is in the middle (the Ham Band :-).



Similarly, the VHF tuning range is extended in the same manner.  After

the mod is made, the VHF side will apparently tune from between 100-199

mhz but as stated above, there is little or no response outside of the

published range (138-170 mhz), due to the same reasons as stated

above.



As a final side effect, note that performing this mod will remove all

out-of-band transmit restrictions on the rig, for both VHF and UHF.

After the mod is in place, the radio will transmit on any frequency

that it can tune to.



DISCLAIMER:



The author of this report wishes to strongly remind those who perform

this mod that it is ILLEGAL to transmit on any frequencies outside of

the ham bands, EVEN IF YOU ARE OTHERWISE LICENSED TO DO SO.  This is

because of the radio's lack of FCC type acceptance for these

frequencies.  So beware!  Unauthorized use of this feature could be

hazardous to your ticket.  MARS/CAP users are probably OK with a permit.





Now for the nuts and bolts.....





MODIFICATION PROCEDURE



1. Turn the radio on and write down all of your memory channel

frequency assignments, PL codes and anything else you have in memory -

It will all have to be reprogrammed after the mod.  After writing down

all of your data, turn off the unit and disconnect it from the antenna

and power supply.



2. Next, remove the bottom cover on the unit.  Note:this radio

contains a number of CMOS parts which could be damaged by static

discharge.  Take all of the regular precautions to make sure that you

and your tools are properly grounded for anti-static work.  Note that

there is a hole in the rear of the subchassis which supports the

controller circuit board in which you can see a small, black, 1/4 watt

resistor which is labeled on the board as R57.  Using a small pair of

sharp cutters, clip the lead on the end of the resistor.  It is not

necessary to remove the part, just clip one end and bend it slightly

out of the way.



2. Next, remove the top cover and then open the front panel assembly

into the service position.  To do this, remove the four silver screws,

one on the top, one on the bottom, and one from each side.  Two of the

screws are in slotted holes.  Loosen the screws in the slotted holes

slightly so as to allow the front panel to be pulled out and swung down

in a hinge-like fashion.  Once open, set the radio on a table with the

hinged front panel hanging over the edge of your workbench.

Familiarize yourself with the inside of this compartment.  The most

notable features are a silver, button type lithium battery to the left

of center and a large, multi-pin microprocessor chip on the right.  DO

NOT DISCONNECT ANY OF THE RIBBON CABLES.



3. Locate the lithium battery and to it's left you will notice a row of

five programming resistor positions, with the middle position vacant.

The arrangement looks something like this:



|

|                        ____                    ______

|       I I:II          (Bat-)                   |MPU |

|                       (tery)                   |    |

|                        ----                    ------

|

|                  I <- R121 (remove for cross-band repeater operation)

______________________________________________



        VVV front of rig VVV



The (:) above indicates where a jumper is to be placed.  Use care in

soldering since everything is quite small.



4. Reassemble the unit in the reverse order as described above.  When

you power the rig up, the display should show 440.000 and 144.000 on

the displays.  It is now ready for operation.  If necessary, perform

the microprocessor reset function by holding down the F button while

turning on the power.  Reprogram the unit with the data you saved in

step 1.





Comments:



There is nothing special about operating the rig once the modification

is made.  All functions operate exactly as before except that the range

on each band is extended as described above.  You will probably want to

program the band scan limiting channels (A and B) on both bands since

otherwise your vfo scanning will be too broad and will spend a lot of

time scanning in areas which it cannot receive.



In addition, my rig also has the cross-band repeater mod.  I do not

know if having this is a prerequisite to performing the mod mentioned

above.  If it is, then R121 will also have to be removed.  The cross-

band repeater mod has already been discussed on the net so I won't go

into it at this time.



Enjoy this mod but don't endanger your license!  Don't transmit out of

band and don't allow others to, even if they're licensed for those

frequencies!



-fred



--------------------------------------------------------------------

| Fred Lloyd  AA7BQ

--------------------------------------------------------------------